TOTO cast iron bathtub how to install cast iron bathtub

The Cast Iron Bathtub is made of cast iron, and its surface is covered with enamel. It has smooth and smooth surface, moist color, anti-fouling, low water injection noise, easy cleaning, and durability. It is widely used in the building materials market. So how to install the cast iron bathtub? In this issue, Xiaobian will introduce the steps of installing the TOTO cast iron bathtub, and follow the Xiaobian to understand it.

First, TOTO bathroom. Cast iron bathtub

Since TOTO Sanitary Ware Co., Ltd. was founded in 1917, TOTO has challenged the traditional concept of sanitation that has been accepted by the public with its outstanding products. Until today, TOTO has become a famous sanitary enterprise.

Because of the thick bathtub wall, the cast iron bathtub is characterized by its excellent insulation properties and is favored by some consumers who value thermal insulation properties; low water injection noise, easy cleaning, acid and alkali resistance and chemicals, high gloss and so on. The various characteristics become an insurmountable advantage for acrylic bathtubs and other materials. Therefore, the price of a cast iron bathtub is generally 2-3 times that of an acrylic bathtub. Their installation procedure is the same as the embedded bathtub, but the cast iron bathtub is much heavier, but it can be used almost for once, so buying a cast iron bathtub is a good choice.

Second, TOTO cast iron bathtub installation

The first step: test whether the water leaks.

Place the bathtub before the first water accessories, do water for 24 hours to see if the bathtub is leaking, pay special attention to the overflow. It's very difficult to close the water in 24 hours. Outside the bathroom, pour two buckets of water and try a good bathtub to get water. This is convenient. At the time of actual installation, the bathtub was directly lifted into the bathroom and placed in the water. Since the width of the bathtub was just the same as the width of the bathtub when the water was changed, the size of the bathtub and the mixing of water was not correct. Note that the center point of the bathtub should be facing the center of the mixing water, otherwise it will be very difficult to see if the mixing faucet is installed in the future.

After the bathtub is lifted into the bathroom, it starts to put on and off the water fittings, fills the bathtub with water, closes the water, and checks for leaks. When the water flows over the overflow, the water in the bathtub flows out of the overflow. This time, go Touch the back of the spill to see if water leaks out from here. After the overflow test is passed, the next step is to check the sealing of the sewage, and to select the method of standing and observe the tightness of the sewage.

The second step: leveling the bathtub.

When placing the bathtub, take care that the other end of the water outlet is slightly higher than the end of the drain so that the sewage will not be discharged in the future. This depends on the circumstances. Observe that the bottom of the bathtub had a slope for draining water, level the bathtub on the four sides, and put a water test. As expected, the water quickly drained. The bathtub visually maintains a level of beauty without affecting the effect of drainage

The third step: fill sand.

Although the cast-iron bathtub is strong, its thermal conductivity is very fast. It should be used in Zhonghesha and it should be firmly laid on the bottom of the bathtub. Bricklayers also recommend the use of foam. Considering that foam is not as mobile as sand, it is ideal to fill all the gaps. In the process of filling sand, how to make sand not leak into the sewage pipe is a problem to be solved.

After all the placement work was completed, the water release test was performed again (this step was mainly to ensure that the backside of the bathtub did not leak water). After confirming it was correct, it waited for the bricklayer to lay the skirt.

Step 4: Leave the access port.

A 300mm wide 400mm hole is left at the water outlet, and one hole is cut to size. The board is made of water-repellent and anticorrosive wood (thickness 40mm) according to the size. The number of bricks and the number of rows arranged on the board are 903. The glue sticks the brick to the board. Extend the edge of the brick with a sealant and insert it on the box. This is to facilitate the overhaul of the bathtub drainage system in the future. In the bathtub skirt, for aesthetic considerations, all set aside 600 heights, give up other materials such as mosaics, bath skirts and the same brick under the wall brick, so to do, under the wall tiles, floor tiles, bath skirts are all One color, one material, very beautiful.

Step 5: Tiling

Bathtub skirt tiles do not need to scratch the hair, build a red brick table, a layer of cement mortar on the surface, and then wait two days and then tiling can, tiling is very troublesome, due to the slope of the ground to stay, and the bathtub It's flat, so every big brick must be polished to different sizes. It's not possible to polish a lot at a time, it's easy to grind, and it's repeated. The top of the brick is to be inserted under the round edge of the bathtub so that it does not form an angle.

Reminder: For more information, please pay attention to the information on this website , or you can visit our offline experience directly.

More exciting recommendations

Huida bathroom prices

American standard bathroom official website

Faenza bathroom how

Wrigley how to bathroom

Kohler bathroom how

Sanitary Ware Top Ten Brands

Bathtub Kohler bathtub bathroom bathroom faucet cement building material market red brick